NTSB CAROL · Event
Event CHI96FA216
Aircraft involved
Probable cause & findings
insufficient clearance between the second stage compressor impeller and the shroud. A factor was the subsequent fatigue failure of the impeller.
Factual narrative
HISTORY OF FLIGHT
On June 26, 1996, at 1430 central daylight time, a Fairchild SA227AC, N2692P, operated by Mesaba Airlines as Northwest Airlink flight 3253, sustained substantial damage following an uncontained failure of the number two engine during climb. The flight returned to Grand Forks, North Dakota and landed without further incident. The flight crew and 17 passengers reported no injuries. The 14 CFR Part 135 flight departed Grand Forks, North Dakota, about 1430 with a planned destination of Minneapolis, Minnesota. Visual meteorological conditions prevailed and an IFR flight plan was filed. The captain reported that airplane was at an altitude of 5,000 feet mean sea level. The propeller rpm was 100 percent and other engine indications were "normal." The loss of power on the number two engine was "sudden and immediate." Air traffic control transcripts indicate the airplane was ten miles south of Grand Forks. The flight crew declared an emergency and recovered visually to Grand Forks without further incident.
DAMAGE TO AIRCRAFT
Examination of the airplane by Federal Aviation Administration Inspectors revealed eleven impact marks to the right side of the fuselage. Two of the impacts penetrated the fuselage side. The propeller exhibited minor damage. The number two engine was removed and transported to Minneapolis, Minnesota for subsequent examination.
TESTS AND RESEARCH
The number two engine was examined on July 23, 1996, at Mesaba Airlines maintenance facility, Minneapolis, Minnesota. The direct drive fuel control (DDFC) idler gear assembly was dislodged and was protruding through a hole in the gearbox inlet section. Several fragments of the gearbox were recovered. The engine mounts were intact. The compressor bearing retainer was fractured. The tie-bolt was fractured forward of the center curvic splines. The high speed pinion was fractured at the shear section. The compressor bearing outer race was fragmented and the balls were missing. The turbine bearing was fractured in several places. The second stage compressor impeller rim was fractured. Several fragments of the impeller were imbedded in the transition liner and the diffuser. The impeller shroud exhibited a circumferential rub. Corresponding rubbing was evident on the "shroud line edge" of the impeller and impeller fragments. "Thick layers of aluminum rich deposits" were fused to the impeller. Examination of the impeller and impeller fragments revealed multiple fatigue fractures emanating from the rubbed shroud line edge. Scanning electron microscopic examination of the fatigue areas revealed evidence of "high cycle fatigue." A section of one of the impeller fragments revealed "highly heat affected (transformed) structure emanating from the heavily rubbed shroud line edge." No material defects were noted. Examination of the gear box fragments revealed fracture surfaces "indicative of an overload fracture mode... no material defects or cyclic fatigue propagation were observed." An Allied Signal product integrity engineer reported that the tolerance between the impeller and shroud is accomplished via shims during engine assembly. He reported that the shims in the number two engine were all within acceptable limits. Additionally he reported that the dynamic clearance can be affected by operational conditions such as extended use of engine anti-ice at excessive temperatures. Examination of Mesaba Airlines SA-227 Pilot Operating Handbook revealed "the use of engine inlet anti-ice is restricted to ten seconds of use on the ground when the OAT is above +5 degrees Celsius regardless of engine RPM."The TPE331 installation manual specifies "inlet anti-icing should not be used above 50 F ambient conditions for more than ten seconds."
ADDITIONAL INFORMATION
Parties to the investigation were the Federal Aviation Administration, Mesaba Airlines, the Airline Pilots Association, and Allied Signal Aerospace. The captain reported that the airplane was at 5,000 feet mean sea level, the propeller rpm was 100 percent, and other engine indications were normal. A loss of power on the number two engine was 'sudden and immediate.' The flightcrew declared an emergency and recovered visually to Grand Forks without further incident. Examination of the airplane revealed eleven impact marks to the right side of the fuselage. Two of the impacts penetrated the fuselage side. Examination of the engine revealed evidence of overload failure and penetration of the gear box. Fatigue fractures in the second stage compressor impeller rim emanated from a heat affected, rubbed area on the impeller blades. A corresponding rubbed area was evident on the impeller shroud, and aluminum material was fused to the titanium impeller. No evidence of material defects were noted. Source: NTSB Aviation Accident Database (Pre-2008 Archive) Retrieved: 2026-02-12
Verbatim from NTSB's published report. Source file
NTSB_1996_CHI96FA216.txt.
Findings + structured fields enriched from FAA avall.mdb.
Full investigation docket on
data.ntsb.gov ↗.
Beyond the agency record
Search this event elsewhere.
Pre-filled searches into the sources where news + community discussion of aviation events lives. External sources are reported, not agency. Treat them as signal that something happened, not as fact about what happened.
Entity-clustered aviation events in the press — last 24 hr + 30-day archive.
Official agency record + docket.
Investigative docket: factual reports, photos, transcripts.
Long-running aviation incident database (Flight Safety Foundation).
Community NTSB synthesis blog — often has photos and witness reports.
Gold-standard aviation incident blog.
Aviation industry news search.
GA pilot forum — informed but rumor-prone.
GA pilot subreddit search.
Tail-number page — flight history (free tier limited).
AOPA Air Safety Institute search.
Mainstream press coverage. Recent events only.
Privacy-preserving news search.
External links open in a new tab. We don't ingest their content; we deep-link search queries.
Related research
What the literature says.
Academic papers and agency reports matching this event's aircraft type or causal vocabulary (icing, stall, maintenance). Sourced from NASA NTRS, NTSB Safety Studies, FAA CAMI, AOPA Air Safety Institute, Embry-Riddle Scholarly Commons, arXiv, and the Semantic Scholar academic graph.
- Embry-Riddle Scholarly Commons 2023 · Faculty research project
Reconfigurable Guidance and Control Systems for Emerging On-Orbit Servicing, Assembly, and Manufacturing (OSAM) Space Vehicles
Dynamic response to emergent situations is a necessity in the on-orbit servicing, assembly, and manufacturing (OSAM) field, because traditional on-orbit guidance and control (G&C) cannot respond effic…
- arXiv 2023 · arXiv preprint
Variation of Critical Crystallization Pressure for the Formation of Square Ice in Graphene Nanocapillaries
Two-dimensional square ice in graphene nanocapillaries at room temperature is a fascinating phenomenon and has been confirmed experimentally.
- Embry-Riddle Scholarly Commons 2023 · Conference paper
The Value of Strong Partnerships to Build a Successful Aviation Maintenance Career Pathway Program for Transitioning Military Service Members
The aerospace industry is competing with other industries for a qualified workforce, and many of those competing industries are investing heavily in creating workforce development pipelines.
- arXiv 2022 · arXiv preprint
Enhanced Prediction of Three-dimensional Finite Iced Wing Separated Flow Near Stall
Icing on three-dimensional wings causes severe flow separation near stall. Standard improved delayed detached eddy simulation (IDDES) is unable to correctly predict the separating reattaching flow due…
- NASA NTRS 2019 · Contractor Report (CR)
An Evaluation of an Analytical Simulation of an Airplane with Tailplane Icing by Comparison to Flight Data
This report presents the assessment of an analytical tool developed as part of the NASA/FAA Tailplane Icing Program. The analytical tool is a specialized simulation program called TAILSM4 which was de…
- NASA NTRS 2019 · Technical Publication (TP)
NASA/FAA Tailplane Icing Program: Flight Test Report
This report presents results from research flights that explored the characteristics of an ice-contaminated tailplane using various simulated ice shapes attached to the leading edge of the horizontal …
Browse the full corpus — academia portal ↗